| Tester, Meters, and Monitors |
| | |  |
Pocket TDS-meter
|
Item part : TDS
Range: 0-2999 ppm
Accuracy: 1 ppm
Auto shut off function (battery saving)
Auto hold function (reading stays even tester is not in water)
Automatic temperature compensation
Backlight color indicator of water quality:
green: < 40 ppm
red: > 40 ppm
|
|
 |
|
Dual TDS-meter
|
Item part: TDS-BA
Range: 0-999 ppm
Sensitivity: 1 ppm
Meassures water quality before and after treatment
Includes 2 diverter T's (available on 1/4" and 3/8")
Selectable for continuous monitoring or button control meassure (battery saving)
Dimensions: 4" (H) x 1.6" (W)
Backlight color indicator of removal rate:
flash green: > 80%
flash red: < 80%
|
| |  |
Pocket pH-meter
| Item part : PH
Range: 0-14.0
Accuracy: ±0.1 + 1 dígito
Resolution: 0.1
Temperature compensation: Automatic
Operate with 3 of 1.5V batteries, or 9V
Buffer solution for calibration included
|
| |  |
Panel-mount In-Line Conductivity meter
| Item part : TDS-IL
Range: 0-20, 0-200, 0-2000 μS/cm
Accuracy: 1.5%
Temperature compensation: Automatic
Output signal 4-20 mA
Sensor thread: 1/2"
Hole size on panel: 1.8" x 3.5" |
| | |
Panel-mount In-Line Conductivity meter with Buzzer
| Item part : TDS-IL-A
Alarm regulable for high and low TDS level
Range: 0-20, 0-200, 0-2000 μS/cm
Accuracy: 1.5%
Temperature compensation: Automatic
Sensor thread: 1/2"
Hole size on panel: 1.8" x 3.5" |
| | |
Panel-mount DUAL Conductivity meter with buzzer
|
Item part : TDS-BA-A
Alarm for high and low TDS level
Includes 2 conductivity sensors, for IN and OUT meassure
Range: 0-20, 0-200, 0-2000 μS/cm
Accuracy: 1.5%
Temperature compensation: Automatic
Sensors thread: 1/2"
Hole size on panel: 1.8" x 3.5"
|
| |  |
Panel-mount ORP controler
| Item part : ORP
Range: 0-1000 mV
Resolution: 1 mV
Sensitibity: 1 mV
Output signal 4-20 mA
Temperature compensation: Manual
Hole size on panel: 1.8" x 3.5" |
| | |
Panel-mount Controler
| Shows operation status of a reverse osmosis system thruough flow diagram
Status shown: low inlet flow, low inlet pressure, high inlet pressure, high TDS level
Hole size on panel: 1.8" x 3.6"
|
| |  |
Panel-mount Controler with Conductivity meter
| Status controler, operation tester and water quality monitor on the same instrument
Shows operation status of a reverse osmosis system through flow diagram
Combine PLC controler functions with a TDS meter
Process controled:
* Low inlet flow: a light will turn-on and will send a signal to shut-off the RO unit
* Low pressure after prefilters: a light will turn-on and the alarm will send a signal to the controler to shut-off the RO unit, then to restart after 1 minute for 3 times
* High pressure after the pump: a light will turn-on and the alarm will send a signal to the controler to shut-off the RO unit, then to restart after 1 minute if pressure have been released
* High conductivity level: a light will turn-on and the alarm will send a signal to the controler to activate a relay that can open a drain valve
Hole size on panel: 3.6" x 3.6"
|
| | |
GF Signet and Myron L Instruments
| For detailled information on these products, visit manufacturer web site: |
| | | |
|
